Posted: 21 Jun 2005
My friend's brother had a 512MB Lexar Media Jumpdrive Pro USB drive that
became corrupted after using it with Windows 2000. His IT department was able to
get back some but not all of the file contents, but without any file names. On
his own, he tried some recovery utilities, but all failed. Using a typical Linux
distro--in this case SuSE 8.0--however, it wasn't hard to recover almost all of
the data from the drive along with the filenames and to burn a CD-ROM of the
contents.
USB Drive Ruined by Windows
Here's what I heard about the data loss:
Date: Sun, 1 Aug 2004 17:06:03 -0700
Subject: USB
... My USB drive is a
Lexar Media USB Jumpdrive Pro 2.0 (512 MB). I was working
on it in a computer with Windows 2000 and logged off before
ejecting the drive. Next time when I tried to use it,
it showed up as a Removable drive rather than the usual
Lexar Media drive and when I tried to open it, it said the
drive was not formatted; and under Properties, 0 bytes free
and used space and file system "RAW"
According to Lexar tech support, there is a bug with
Windows 2000 (that MS never bothered to fix) and can corrupt
the drive when it is removed without proper eject. They
recommend EasyRecovery Pro for data recovery which did
allow me to recover some files (> 500) using their RAW data
recovery program (all other tool failed because usually
said "no recognizable file on disc"). Unfortunately,
all the file names are lost and some files are gone.
The big questions was "can Linux read the drive?" A Web search of "linux usb
jumpdrive pro" gave me hope that my kernel, 2.4.18 on SuSE 8.0, would recognize
the drive in question. So, as root, I typed:
# tail -f /var/log/messages
and plugged the drive into a USB socket. Here's what appeared; I removed "Aug
5 01:32:15 linux kernel:" from each line below):
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
usb-uhci.c: interrupt, status 3, frame# 1313
Vendor: LEXAR Model: JUMPDRIVE PRO Rev: 0
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 1001952 512-byte hdwr sectors (513 MB)
sda: Write Protect is off
sda: sda1
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 4
USB Mass Storage support registered.
Encouraged by that report, I tried this:
# dd if=/dev/sda of=/tmp/r1 bs=512
which reported that 1,001,952 blocks had been transferred. I then unplugged
the drive and did the rest of my work using the image stored in
/dev/sda.
Condition of the Boot Sector
The master boot record, which is the boot sector for the entire drive and its
first sector, has a partition table, as well as other interesting things:
# od -Ax -tx1 /tmp/r1 | less
...
*
0001b0 00 00 00 00 00 00 00 00 48 04 07 c9 00 00 80 01
0001c0 01 00 06 0f ff e0 3f 00 00 00 b1 45 0f 00 00 00
0001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
0001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa
The boot sector has a reasonable-looking partition table with one entry. It
began at offset 0x1be, the two bytes 80 01. Your favorite search engine can give
you other information about the partition table, but I note two things here.
First, the entry has an LBA32 format--starting logical sector 0x3f, length
0xf45b1. Now, 0xf45b1 is 1000881 decimal. That plus 63 (0x3f) is 1000944. The
difference between the 1001952 and this 1000944 is 1008, that is, 63*16. I guess
this has something to do with cylinder boundaries. The second thing of note is
the byte at 0x1c2, with value 06; this is the partition type. What does 06
mean?
Typing fdisk /dev/hda as root and giving the command l to
list, shows that type 6 is:
0 Empty 1c Hidden Win95 FA 65 Novell Netware bb Boot Wizard hid
1 FAT12 1e Hidden Win95 FA 70 DiskSecure Mult c1 DRDOS/sec (FAT-
2 XENIX root 24 NEC DOS 75 PC/IX c4 DRDOS/sec (FAT-
3 XENIX usr 39 Plan 9 80 Old Minix c6 DRDOS/sec (FAT-
4 FAT16 <32M 3c PartitionMagic 81 Minix / old Lin c7 Syrinx
5 Extended 40 Venix 80286 82 Linux swap da Non-FS data
6 FAT16 41 PPC PReP Boot 83 Linux db CP/M / CTOS / .
...
So, it's FAT16.
Now, if I had been watching carefully, I would have known from the line
sda: sda1 in /var/log/messages that the partition table was okay and
contained only one entry.
Finding the FATs
When I actually started looking, however, I wasn't really sure if this was a
FAT16 vs FAT12. The drive's capacity of 512MB suggested it could be either FAT16
or FAT32. I also somehow had the impression that the partition could have
contained a FAT32 filesystem in the same partition type. As I continued to look
through the filesystem, I noticed this:
# od -Ax -w8 -tx1 -tc /tmp/r1 | less
045400 4c 45 58 41 52 20 4d 45 L E X A R M E
045408 44 49 41 28 00 00 00 00 D I A (
045410 00 00 00 00 00 00 4b 5a K Z
045418 33 2b 00 00 00 00 00 00 3 +
045420 41 52 00 53 00 54 00 55 A R S T
045428 00 4c 00 0f 00 9a 6f 00 L 017 232 o
045430 67 00 2e 00 78 00 6c 00 g . x l
045438 73 00 00 00 00 00 ff ff s
045440 52 4e 41 4c 4f 47 7e 31 R S T L O G ~ 1
045448 58 4c 53 20 00 b8 03 61 X L S 003 a
045450 50 30 e4 30 00 00 ca 74 P 0 0 t
045458 4b 30 f2 6a 00 3e 00 00 K 0 j >
...
On a side note, I recently discovered the hard way that CMD | less
doesn't do what you want it to if the output of CMD is too long. In this case it
was okay to use, but it isn't always; this probably is system-dependent. If you
have enough space on your hard drive, it may pay to do something like this:
# od -Ax -w8 -tx1 -tc /tmp/r1 > /tmp/r2; less r2
or
# hexdump -C /tmp/r1 > /tmp/r2; less r2
So this looks like the start of a directory. Immediately above that area,
though, I saw this:
042420 00 00 00 00 00 00 14 dd 15 dd 16 dd 17 dd 18 dd
042430 19 dd 1a dd 1b dd 1c dd 1d dd 1e dd 1f dd 20 dd
042440 21 dd 22 dd 23 dd 24 dd 25 dd 26 dd 27 dd 28 dd
042450 29 dd 2a dd 2b dd 2c dd 2d dd 2e dd 2f dd 30 dd
042460 31 dd 32 dd 33 dd 34 dd 35 dd 36 dd ff ff 00 00
042470 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
That looked like an allocation chain with 16-bit entries. If these had taken
the form 31 dd 00 00 32 dd 00 00 rather than 31 dd 32 dd, I
might have thought I was looking at FAT32.
I had heard somewhere that typically two FATs can be found together, one
right after the other. I told less(1) to find another line resembling the line
at 0x42460, by typing ?31 dd 32 dd 33 dd. In response, less(1) showed
me this:
023a20 00 00 00 00 00 00 14 dd 15 dd 16 dd 17 dd 18 dd
023a30 19 dd 1a dd 1b dd 1c dd 1d dd 1e dd 1f dd 20 dd
023a40 21 dd 22 dd 23 dd 24 dd 25 dd 26 dd 27 dd 28 dd
023a50 29 dd 2a dd 2b dd 2c dd 2d dd 2e dd 2f dd 30 dd
023a60 31 dd 32 dd 33 dd 34 dd 35 dd 36 dd ff ff 00 00
023a70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
026a00 f8 ff ff ff 03 00 e6 02 21 03 a0 03 15 03 91 03
026a10 ff ff 0a 00 0b 00 ff ff 0d 00 0e 00 0f 00 10 00
The data at 0x42460 and at 0x23a60 are the same; this told me that the offset
between tables was:
0x42460 - 0x23a60 = 0x1ea00
because 0x26a00 is the start of FAT#2. Therefore, the start of FAT#1 should
be at
0x26a00 - 0x1ea00 = 0x08000
But when I looked there, I saw this instead:
007c00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
*
012400 01 52 02 52 03 52 04 52 05 52 06 52 07 52 08 52
012410 09 52 0a 52 0b 52 0c 52 0d 52 0e 52 0f 52 10 52
012420 11 52 12 52 13 52 14 52 15 52 16 52 17 52 18 52
Somebody had written a whole mess of 0xff bytes. I guess this was part of the
corruption.
At this point, 0x12400 looked okay, but was it? What's in the corresponding
place in FAT#2?
0x12400 + 0x1ea00 = 0x30e00
030e00 01 52 02 52 03 52 04 52 05 52 06 52 07 52 08 52
030e10 09 52 0a 52 0b 52 0c 52 0d 52 0e 52 0f 52 10 52
030e20 11 52 12 52 13 52 14 52 15 52 16 52 17 52 18 52
Luckily, this looked okay too. In fact, FAT#2 might be completely okay even
though the first 40KB or so of FAT#1 had been corrupted.
Repair Attempt #1
All of this has been interesting, but the point of this exercise was to
repair the filesystem and read the data. So I now turned to my friend fsck for
the repair work, in particular fsck.msdos, err and dosfsck(8). I took the
filesystem image and did what needed to be done with a spare loop device:
# losetup /dev/loop2 /tmp/r1
# fsck.msdos /dev/loop2
But according to fsck.msdos(8), the "disk" claimed to have something near 165
FATs, whereas fsck.msdos only supports two. Apparently, some filesystem
parameters were messed up severely.
Shortcut to Filesystem Repair
I started looking at the source code for mkfs.msdos, also known as
mkdosfs(8), but then came up with a better idea. What if I could create a
filesystem with the FAT parameters arranged so that the FATs and the directory
in this new filesystem were in the same place where the FATs and directory were
in the disk image I already had? The bytes that read LEXAR MEDIA probably were
the volume name. Maybe, by giving the right parameters to mkfs.msdos(8), I could
create a filesystem image wherein 0x08000 would point to the first FAT, 0x26a00
would point to the second FAT and 0x45400 would point to the volume label.
On the mkdosfs(8) manpage, I found:
SYNOPSIS
mkdosfs [ -A ] [ -b sector-of-backup ] [ -c ] [ -l file
name ] [ -C ] [ -f number-of-FATs ] [ -F FAT-size ] [ -i
volume-id ] [ -I ] [ -m message-file ] [ -n volume-name ]
[ -r root-dir-entries ] [ -R number-of-reserved-sectors ]
[ -s sectors-per-cluster ] [ -S logical-sector-size ] [ -v
] device [ block-count ]
Therefore, I specified -f 2 for two FATs and -n
mkfs__msdos--that is, a string I could find easily--for the volume name.
This way I could tell where the vol-name landed.
How about the other parameters? I saw above that the FATs were 0x1ea00 bytes
apart; if they landed the wrong distance from each other, I could tweak -F and
maybe -s. I found on-line that for a filesystem of this size, the clusters would
be 8192 bytes; in other words, there would be 16 512-byte sectors per cluster.
The cluster is the file allocation unit described by the FAT. Hence, it would be
-s 16.
As for where to create the filesystem, it wouldn't do to put it on the USB
drive. Instead, I created a file the same size as the drive image but filled
with zeroes:
# dd if=/dev/zero of=/tmp/r2x bs=512 count=1001952
After creating the filesystem, I figured I'd mount it and create a file. The
file would have enough data in it that we could see a reasonable allocation
chain. To accomplish this, I wrote a script and prepared to call it with
parameters until I happened to find everything where I wanted it. I called it
b.sh:
#!/bin/bash
# parameters added to mkfs.msdos....
ARGS="$*"
if mount | grep /tmp/r2d; then umount /tmp/r2d; fi
losetup -d /dev/loop2
losetup /dev/loop2 /tmp/r2x
mkfs.msdos -n mkfs__msdos -s 16 $ARGS /dev/loop2
mount -t vfat /dev/loop2 /tmp/r2d
yes hello | dd bs=8192 count=3 of=/tmp/r2d/foo.txt
umount /tmp/r2d
My plan was to try running this script with different parameters until I got
it right. 0x8000 is 32KB. In 512-byte sectors, that's 64. Because the first FAT
started at 0x8000, I decided to try -R 64, like this:
# sh b.sh -R 64
mkfs.msdos 2.8 (28 Feb 2001)
Loop device does not match a floppy size, using default hd params
2+1 records in
2+1 records out
#
The surprising thing was my first guess turned out to be right, at least as
far as the FAT placement:
# hexdump -C /tmp/r2x | less
...
00008000 f8 ff ff ff 03 00 04 00 f8 ff 00 00 00 00 00 00 |..........|
00008010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00026a00 f8 ff ff ff 03 00 04 00 f8 ff 00 00 00 00 00 00 |..........|
00026a10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00045400 6d 6b 66 73 5f 5f 6d 73 64 6f 73 08 00 00 71 89 |mkfs__msdos...q.|
00045410 0f 31 0f 31 00 00 71 89 0f 31 00 00 00 00 00 00 |.1.1..q..1......|
00045420 41 66 00 6f 00 6f 00 2e 00 74 00 0f 00 65 78 00 |Af.o.o...t...ex.|
00045430 74 00 00 00 ff ff ff ff ff ff 00 00 ff ff ff ff |t.....|
00045440 46 4f 4f 20 20 20 20 20 54 58 54 20 00 00 71 89 |FOO TXT ..q.|
00045450 0f 31 0f 31 00 00 71 89 0f 31 02 00 00 50 00 00 |.1.1..q..1...P..|
00045460 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00049400 68 65 6c 6c 6f 0a 68 65 6c 6c 6f 0a 68 65 6c 6c |hello.hello.hell|
00049410 6f 0a 68 65 6c 6c 6f 0a 68 65 6c 6c 6f 0a 68 65 |o.hello.hello.he|
...
I didn't check the directory size, but it apparently it was okay as
well--more on that below.
Grafting Filesystems
I now had a boot sector that would tell fsck.msdos to expect the FATs and the
root directory at all the right places. So what if I created a filesystem image
where the first sector was that one, but all the rest of the sectors contained
data from the USB drive? Then, fsck.msdos would read the boot sector; I'd tell
it to use FAT#2 to repair everything; and we'd see how it turned out.
Repair Attempt #2
To summarize exactly what fixed the USB device:
# dd if=/dev/zero of=/tmp/r2x bs=512 count=1001952
# losetup /dev/loop2 /tmp/r2x
# mkfs.msdos -n mkfs__msdos -s 16 -R 64 /dev/loop2
# dd if=r1 of=r2x bs=512 skip=1 seek=1
# fsck.msdos -f -r /dev/loop2
Because I knew that FAT1 was bogus, I told it to use FAT2, and it reported
success. It asked me whether to write the changes, and I said yes.
The filesystem images in /tmp/r2x and /dev/loop2 now were consistent. The
acid test was to try to mount the filesystem:
# mkdir /tmp/r2d
# mount -t vfat /dev/loop2 /tmp/r2d
# ls -lRA /tmp/r2d
After which all kinds of good stuff appeared.
Note: A good result to ls -lR showed that I was lucky in one other
way: I didn't know if the boot sector had a good value for the size of the root
directory, the -r parameter to mkfs.msdos. I simply used the default and it
turned out fine.
Burning CDs
At this point, I decided I had better burn a CD. I burn and read CDs all the
time on Linux, but I rarely burn CDs to be read by Windows. Again I did a Web
search, and a page from IBM's DeveloperWorks site turned up. I had searched
"linux burn CD windows" or something like that. So I tried this:
# mkisofs -J -r -v /tmp/r2d |
cdrecord -v -pad -eject fs=4m speed=4 dev=0,0,0 -
I wasn't 100% sure that Windows would like this CD, but fortunately I have
Windows95 under Win4Lin. Its sole purpose for me is to run Quicken and TurboTax,
but I fired it up and pointed Windows Explorer at the just-burned CD-ROM.
Explorer loved it. I used gimp(1) to capture a screenshot and e-mailed the image
to my friend's brother--he was ecstatic.
APPENDIX: The Bash Script Explained
Shell jockeys need not read this.
1 #!/bin/bash
2 # parameters added to mkfs.msdos....
3 ARGS="$*"
4 if mount | grep /tmp/r2d; then umount /tmp/r2d; fi
5 losetup -d /dev/loop2
6 losetup /dev/loop2 /tmp/r2x
7 mkfs.msdos -n mkfs__msdos -s 16 $ARGS /dev/loop2
8 mount -t vfat /dev/loop2 /tmp/r2d
9 yes hello | dd bs=8192 count=3 of=/tmp/r2d/foo.txt
10 umount /tmp/r2d
Line 1 identifies to exec(2) that this is supposed to be run by the shell.
I've become accustomed to bash, the Bourne again shell.
Line 2 simply explains line 3, that the parameters you type after
b.sh are parameters to add to the mkfs.msdos command line.
Lines 4-6 establish /dev/loop2 as the block device whose contents are in the
filesystem image kept in /dev/r2x. Line 4 unmounts the artificial filesystem if
it was mounted; this is done because we're about to make some changes to it.
Lines 5-6 make sure that /dev/loop2 is connected to /tmp/r2x and only to
/tmp/r2x.
Line 7 creates an artificial filesystem image with whatever additional
parameters the user gave--remember $ARGS from line 3?.
Line 8 mounts the filesystem onto /tmp/r2d. Line 9 creates a file of about
24KB (three clusters), so I have a filename to look for at the beginning of the
directory.
Line 10 then unmounts the artificial filesystem image, so the kernel does not
think there are inconsistencies if I play with /tmp/r2x.
|